Covid 19 DIY Products & Solutions Components and Accessories
DC Power Jack - Female Connector with 2 pin Screw Terminal
If you need to connect a DC power wall wart to a board that doesn't have a DC jack - this adapter will come in very handy! There is a 2.1mm DC jack on one end, and a screw terminal block on the other. The terminals are labeled with positive..
Rs. 25.00
The DHT11 is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires careful timing to g..
Rs. 120.00
DHT11 – Humidity and Temperature Sensor for Arduino and Raspberry Pi B/B+/Raspberry Pi 2.
The four-pin device uses a 1-wire protocol. It’s a snap to connect to your project, requiring VCC, GND, and a pull-up resistor on the single data line. We’ve already seen it used on at least ..
Rs. 95.00
Hot
Diffused Green 5mm LED (Pack of 25)Need some indicators? We are big fans of these diffused green LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project..
Rs. 25.00
Hot
Online Only
Need some indicators? We are big fans of these diffused red LEDs, in fact we use them exclusively in our kits. They are fairly bright so they can be seen in daytime, and from any angle. They go easily into a breadboard and will add that extra zing to your project.
Pack of 25 diffused red LEDS5mm di..
Rs. 25.00
The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electro..
Rs. 299.00
The DS1621 Digital Thermometer and Thermostat provides 9-bit temperature readings, which indicate the temperature of the device. The thermal alarm output, TOUT is active when the temperature of the device exceeds a user-defined temperature TH. The output remains active until the temperature drops be..
Rs. 195.00
DS18B20is 1-wire digital temperature sensor from Maxim IC suitable with 9 to12 bit precision over the range of operation (-55°C to 125°C) .
With an accuracy of ±0.5°C over the range of -10°C to +85° and multiple data logging of temperature spread in wide area network, con..
Rs. 145.00
This is a sealed (waterproof) and pre-wired digital temperature probe, based on DS18B20, 1-wire digital temperature sensor from Maxim IC, providing data in degree Centigrade with 9 to12 bit precision over the range of operation (-55C to 125C). This probe lets you precisely measure temperatures in we..
Rs. 130.00
Hot
This is a module made using DS3231 RTC and AT24C32 EEPROM. DS3231 is an extremely accurate, low cost I2C RTC with integrated temperature compensated crystal oscillator.It also has a built in comparator which monitors the status of VCC to detect power failures and to automatically switch to back..
Rs. 295.00
Sharp's GP2Y1010AU0F is an optical air quality sensor, designed to sense dust particles. An infrared emitting diode and a phototransistor are diagonally arranged into this device, to allow it to detect the reflected light of dust in air. It is especially effective in detecting very fine particles li..
Rs. 450.00
Electric Glue Gun
Description
High Temperature Glue Gun, potent yet portable enough for versatile needs from the lab to your home.
Specification
Operating Temperature: 193°C
Uses 07 mm X 10 cm glue sticks
230 V, 10 Watts
Applications
Artificial flowers
Crafts
Decoration..
Rs. 195.00