Motor Driver Modules & IC
This A3967 Stepper Motor Driver For Arduino is the latest version of EasyDriver v44 co-designed with Brian Schmalz. It provides greater flexibility and control over your stepper motor compared to the older versions.
Features and Benefits:
▪ ±750 mA, 30 V output rating
▪ Satlington&..
Rs. 185.00
A4988 Stepper Motors Driver Module with Heat sink for Arduino/Raspberry-Pi/Robotics
The A4988 stepper motor driver carrier is a breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver. The driver features adjustable current limiting, overcurrent and overtemperature protection,..
Rs. 120.00
This breakout board for Allegro’s A4988 microstepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions (down to 1/16-step). It operates from 8 V to 35 V and can deliver up to approximately 1 A pe..
Rs. 140.00
L293D Arduino motor drive shield for Servo,Stepper And DC Motor
Features:
The shield contains two L293D motor drivers and one 74HC595 shift register.
The shift register expands 3 pins of the Arduino to 8 pins to control the direction for the motor drivers.
The output enable of the L293D ..
Rs. 195.00
L293D is a dual H-bridge motor driver integrated circuit (IC).Motor drivers act as current amplifiers since they take a low-current control signal and provide a higher-current signal. This higher current signal is used to drive the motors.
L293D contains two inbuilt H-bridge driver circuits. In its..
Rs. 42.00
This module is a medium power motor driver perfect for driving DC Motors and Stepper Motors.It uses the popular L293D motor driver IC. It can drive 4 DC motors in one direction, or drive 2 DC motors in both the directions.FeaturesL293D motor driver IC.Male burgstick connectors for supply, ground and..
Rs. 110.00
The L298N driver module, using ST’ L298N chip, can directly drive two 3-30V DC motor, and provide a 5V output interface, power for 5V single-chip circuitry , support 3.3VMCU control. you can easily control the DC motor speed and direction, also control the 2-phase stepper motor.
Features:
..
Rs. 195.00
The L298 is an integrated monolithic circuit in a 15-lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provi..
Rs. 110.00
The L9110S 2-Channel motor driver module is a compact board that can be used to drive small robots. This module has two independent motor driver chips which can each drive up 800mA of continuous current. The boards can be operated from 2.5V to 12V enabling this module to be used with both 3.3V and 5..
Rs. 175.00
-250x250.jpg "Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)")
Out Of Stock
Description: This is essentially a ramped up version of our Ardiumoto motor driver shield. For this Monster Moto Shield we’ve replaced the L298 H-bridge with a pair of VNH2SP30 full-bridge motor drivers. We’ve also beefed up the support circuitry so this board is capable of driving a pair of hi..
Rs. 295.00
Out Of Stock
Features:
2 connections for 5V 'hobby' servos connected to theArduino's high-resolution dedicated timer - no jitter!
4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC.
Up to 4..
Rs. 395.00
You want to make a cool robot, maybe a hexapod walker, or maybe just a piece of art with a lot of moving parts. Or maybe you want to drive a lot of LEDs with precise PWM output. Then you realize that your microcontroller has a limited number of PWM outputs! What now? You could give up OR you could j..
Rs. 345.00