Discontinued Arduino/Genuino MKR1000 (Cortex M0 + WiFi + CryptoChip)
Product Images shown are for illustrative purposes only and may differ from the actual Product. Due to differences in PCB manufacturers, colours, pin mappings, markings & packaging of products/PCBs may also differ from those shown above.
[Update: 7th Feb, 2017]: This product has been retired by Arduino.cc and will not be available anymore :(

Back in Stock! Out of Stock! Coming again by 3rd week of August. Register above to be notified when back in Stock.

Genuino MKR1000 has been designed to offer a practical and cost effective solution for makers seeking to add WiFi connectivity to their projects with minimal previous experience in networking.

The design includes a Li-Po charging circuit that allows the Genuino MKR1000 to run on battery power or external 5V, charging the Li-Po battery while running on external power. Switching from one source to the other is done automatically.

A good 32 bit computational power similar to the Zero board, the usual rich set of I/O interfaces, low power WiFi with a Cryptochip for secure communication, and the ease of use of the Arduino Software (IDE) for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor.

Genuino MKR1000 and Arduino MKR1000 share the same components, characteristics and quality of manufacturing. They are actually the same board under a different brand. Indian Makers will get the Genuino MKR1000 Board. Learn more.

The board will be shipped with male strip header not mounted so you can adapt the board to your project by easily soldering them.

Important noteUnlike most Genuino boards, the MKR1000 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.

Li-Po batteries are charged at 4,2V with a current that is usually half of the nominal capacity (C/2). For Genuino MKR1000 we use aspecialized chip that has a preset charging current of 350mAh. This means that the MINIMUM capacity of the Li-Po battery shall be 700 mAh. Smaller cells will be damaged by this current and may overheat, develop internal gasses and explode, setting on fire the surroundings. We strongly recommend that you select a Li-Po battery of at least 700mAh capacity. A bigger cell will take more time to charge, but won't be harmed or overheated.The chip is programmed with 4 hours of charging time, then it goes into automatic sleep mode. This will limit the amount of charge to max 1400 mAh per charging round.

Discover more at Product Page

Technical specifications

Discover amazing Arduino/Genuino MKR1000 projects here: https://www.hackster.io/arduino/products/arduino-mkr1000-genuino-mkr1000

Write a review

Note: HTML is not translated!
    Bad           Good

Arduino/Genuino MKR1000 (Cortex M0 + WiFi + CryptoChip)

If your required quantity is more than listed below, please ping us for lead time enquiry & to pre-order.


MKR1000 is a powerful board that combines the functionality of the Zero and the Wi-Fi Shield. It is the ideal solution for makers wanting to design IoT projects with minimal previous experience in networking.

GST Invoice for Input Tax Credit.
  • Views: 29763
  • Brand: Genuino
  • Product Code: GENUINO-MKR1000
  • SKU: PL-0-707
  • Availability: Discontinued
  • Rs. 4,360.10
  • Exclusive of GST: Rs. 3,695.00

For bulk & volume priced Corporate/B2B/Academic orders, please contact us for Estimate.

Tags: Arduino, WiFi, Cortex M0, 3.3V

Discuss about this Product
Recent Customer Reviews